hello,

I don’t know if this is the right place to ask this question but could someone explain me how a UEFI system boots, I couldn’t find a guide online. I want to know because I don’t understand certain GRUB commands and how it get installed.

I just copy paste commands from Arch wiki and it just magically works without me knowing anything about it.

all the different distros use different grub command parameter and it’s so confusing. eg, Arch and Gentoo.

Arch command: grub-install --target=x86_64-efi --efi-directory=esp --bootloader-id=GRUB Gentoo command: grub-install --efi-directory=/efi

why both command is different? exactly where does grub gets installed?

sorry if this is a naive question but i really don’t understnad GRUB.

  • folaht@lemmy.ml
    7·
    5 days ago

    GRUB gets installed on your harddisk in your root partition, it’s configuration file on the boot partition and finally into your boot sector if I’m correct. UEFI is a standard for your firmware located outside your harddisk. You go from firmware -> partition layout -> bootloader (grub) -> kernel.

    The firmware is closed source under BIOS or UEFI or if you’re hardcore open source, libreboot/coreboot/‘other options’ and is located somewhere on your motherboard on some chip.
    Then there’s the partition layout and bootloader that are located inside /dev/sda I believe, so inside the device itself, which can be read if you want to take a peek at it.

    Now the bootloader located in the boot sector /dev/sda loaded by the firmware located in some chip in the motherboard, has access to the boot partition, where it loads the bootloader’s configuration file usually located at /boot/grub/grub.cfg for GRUB. I remember UEFI having some kind of standard bootloader by itself, so it doesn’t even need a bootloader if I can remember correctly.

    This what I recall as it was quite complicated for me too. Especially with software being called firmware and not being called motherbootware or pre-bootware or anything that indicates that this piece of software is the very first thing that starts running during boot.

    But you look at /boot and what you can find there. There will be at least two files there called initramfs and vmlinuz, which were also part of the boot process, but I forgot what role those two played.

    • ReversalHatchery@beehaw.orgEnglish
      1·
      5 days ago

      I’m pretty sure UEFI systems don’t make use of a boot sector anymore. They look for the bootloader in the form of an .efi file in the ESP or EFI System Partition, of each sata drive (maybe other block devices too).

      also, the disk it uses is not necessarily “/dev/sda”. first because it can be on any of the disks, second because that’s not a persistent ID but something that depends on detection order

      Especially with software being called firmware and not being called motherbootware or pre-bootware or anything that indicates that this piece of software is the very first thing that starts running during boot.

      firmware is a pretty common term for things like this (code on chip that manages low level startup)

    • neidu3@sh.itjust.worksEnglish
      6·
      5 days ago

      Short answer to your last paragraph:
      vmlinuz is the kernel. It ends with z instead of x, because it’s z-compressed to save space. (I’ve heard that it’s possible to use an uncompressed kernel for that 1ms faster boot time)
      Initramfs (not intramuscular, which my autocorrect thinks is appropriate) is a small filesystem blob, “initial ram filesystem”, meant to be loaded directly into ram to allow the kernel to talk to your hardware via drivers. It also has a lot of binaries needed to perform other tasks that need to run before the root filesystem is mounted.

      • folaht@lemmy.ml
        1·
        5 days ago

        Oh wait, I see that vmlinuz file has a version to it. I couldn’t remember if vmlinuz was the kernel or not, because I used to have multiples of them, but these days I only have one.

        • neidu3@sh.itjust.worksEnglish
          2·
          5 days ago

          You have one per installed kernel. Not sure what (if any) automagic is common for removing old kernels, I guess this varies between distros, but at least on my computers, old kernel remain. At least the previous one, maybe more. It comes in handy in case a kernel upgrade breaks something, which it actually did recently on one of my laptops - makes it easier to boot from old kernel and revert.

          EDIT: I just checked. I have just one on my daily driver. It’s quite new, and I don’t think I’ve had a kernel upgrade on that one, so it makes sense.

          On my work laptop (the one with borked kernel upgrade) I have two.

          So what you most likely have is one or more vmlinuz-version-numbers, and then simply a symlink named just vmlinuz to the version you boot from.